Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 9 - Jul 14
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
SCARPE NIKE PEGASUS 41 GORE-TEX W COBALT/BRONZE/NANike Pegasus 41 GORE TEX Waterdichte hardloopschoenen voor dames (straat) De responsieve demping van de winterklare Pegasus zorgt voor extra energie tijdens je runs op straat bij nat weer. Dankzij de dubbele Air Zoom units en een middenzool van ReactX foam is de schoen licht en profiteer je van energieteruggave. Bovendien helpen een waterdicht GORE TEX bovenwerk en reflecterende designdetails je comfortabel de weersinvloeden te trotseren. Blijf droog
Nike Pegasus 41 GORE-TEX Waterdichte hardloopschoenen voor dames (straat) De responsieve demping van de winterklare Pegasus zorgt voor extra energie tijdens je runs op straat bij nat weer. Dankzij de dubbele Air Zoom units en een middenzool van ReactX foam is de schoen licht en profiteer je van energieteruggave. Bovendien helpen een waterdicht GORE-TEX bovenwerk en reflecterende designdetails je comfortabel de weersinvloeden te trotseren. Blijf droog Het waterdichte GORE-TEX bovenwerk en de technische mesh houden water tegen, zodat je voeten droog blijven. Hallo, ReactX De middenzool van ReactX foam omsluit de voorvoet en de Air Zoom units in de hak zorgen voor extra energie. Afzetten met Zoom De Storm-Tread buitenzool biedt grip bij nat weer. Breder en beter Gemêleerd materiaal rond de kraag helpt je enkels warm te houden. Regenbestendige grip Wat is er nieuw? De gloednieuwe middenzool van ReactX foam is 13% responsiever dan eerdere React technologie. ReactX foam is gemaakt voor performance, en met de planeet in gedachten. Het is ontworpen om de CO2-voetafdruk van een paar middenzolen met ten minste 43% te verminderen dankzij een productieproces dat minder energie vereist dan bij het eerdere React foam. De CO2-voetafdruk van ReactX is gebaseerd op een beoordeling van de volledige levenscyclus, uitgevoerd door PRé Sustainability B.V en Intertek China. Andere componenten van de middenzool zoals Air bags, platen of andere foamformuleringen zijn niet onderzocht. De Pegasus 41 is van binnen gemaakt met dezelfde materialen en vulling als zijn voorganger en zal je voet omhelzen met een geïmplementeerde middenvoetband voor een steviger, maar ook soepeler gevoel. Het bandje om de middenvoet zorgt voor een pasvorm die de vorm van de voet goed volgt, voor voetbogen van elk formaat.Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.8 ★★★★★
Based on 1741 reviews
Sort
Product Reviews
★★★★★ 5
Use the best oil to protect your investment
Configuration: 4-Stroke, Size: 1 GA
Great product.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 30, 2025
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024